Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
CGI
Before
After
Before
After
Before
AfterECO Window Systems Custom & Geometric Windows in Fort Myers: What to Know First
ECO Window Systems custom and geometric windows in Fort Myers typically take two to four weeks from measure to install, with most jobs completed in one to two visits depending on the shape and opening size. As an independent ECO Window Systems service provider, we handle arched, curved, trapezoid, pentagon, and oversized openings for homeowners who already own these products and want them fixed or replaced without starting over. Cost honestly depends on what you have hanging in that opening, but most Fort Myers ECO geometric window jobs on existing frames land between $900 and $3,400 per opening including glass, labor, and a written warranty.
This page is for the ECO Window Systems owner who needs a better answer than “buy new.” Call (239) 323-5522 for a free estimate. A live person answers, even at night.
How ECO Window Systems Products Fail - and How We Fix Them
- Seal failure on radius glass in the ECO 700 Series. In Fort Myers humidity, we regularly see ECO 700 Series arched and half-round windows lose their inert gas fill within six to eight years of install. The tell is a white haze that shows up first in the morning when humidity is highest. Since curved glass is cut, bent, and sealed in a single run, aftermarket curved insulated units are harder to source than flat glass. We size and order custom radius IGUs from a Florida fabricator that matches ECO’s original spacer and edge seal specs, and we document the replacement in writing so the remaining manufacturer warranty authority stays intact.
- Binding sashes on oversized trapezoid units in the ECO Impact line. ECO’s impact-rated geometric windows carry heavier laminated glass than their non-impact shapes. On openings wider than 60 inches, that weight works against the hinge hardware over time, and the sash starts to drag at the latch corner. We see it most on homes in McGregor Boulevard corridor where settled framing throws the opening out of square by an eighth inch or more. The fix is rarely a full replacement. We re-shim, re-square, and replace the hinge assemblies with a heavier gauge spec that ECO’s original install didn’t call for.
- Frame warping at the miter joints on ECO polygon shapes. Pentagon and octagon windows put stress on four corners that square windows never test. ECO’s vinyl line, especially the older 500 Series polygons, can develop hairline cracks at the welded corners after a decade of Florida sun and thermal cycling. Those cracks let water in behind the drywall before you ever see a drip. We open the trim, inspect the corner welds, and either re-seal with a UV-stable structural adhesive or order a replacement sash if the weld has actually separated.
- Obsolete glazing beads on the first-generation ECO circle tops. If your half-round ECO window predates the current extrusion profile, the glazing bead that holds the glass in the frame may be discontinued at the manufacturer level. That’s the kind of information you won’t find on ECO’s own site. We keep a stock of compatible bead profiles and, where an exact match is gone, we’ll machine a replacement bead from the same material and color-match it so the repair is invisible from the driveway.
- Water intrusion at the head flashing on arched units. Arched windows push water into a curved head, and if the original install didn’t use a continuous bent flashing, water follows the curve into the wall cavity. In Fort Myers’s rainy season that shows up as staining at the top corners of the interior jamb. Our fix is a proper bent-metal head flashing with side diverter tabs, sealed with a fluid-applied flashing at the jambs. This is not a caulk-and-pray repair.
Our ECO Window Systems Custom & Geometric Windows Process
- 1
Measure and inspect. Every opening gets measured twice, corner to corner and diagonal to diagonal. On geometric windows, being off by a sixteenth of an inch at the rough opening means a unit that doesn’t seat. We also inspect the existing frame, flashing, and interior trim so you know what’s behind the wall before we touch it.
- 2
Parts decision. We’ll tell you where OEM ECO parts make sense and where a quality aftermarket component does the same job for less. Curved glass units come from a Florida fabricator that matches ECO’s specs. Hardware and glazing beads come OEM when they’re available, and we say so when they’re not.
- 3
Written quote before the work starts. You see the line items, the material sources, and the total on paper before you authorize anything. No change orders, no surprise add-ons when we’re already in the wall.
- 4
The repair or replacement. We do the work carefully and cleanly, protecting your floors and your furniture. Most ECO geometric jobs are done in a single visit. Oversized custom shapes may need a template made on the first visit and installation on the second.
- 5
Test and document. We operate the sash, run a water test on new flashing, and confirm the seal. Then we register the warranty layers in writing before we back out of the driveway.
- 6
Cleanup and follow-up. We leave the room the way we found it. About a week later, we call to make sure the window is still doing what we said it would. If it’s not, we come back and make it right.
What ECO Window Systems Custom & Geometric Windows Costs in Fort Myers
| Job Type | Typical Price Range |
|---|---|
| Single arched or half-round ECO window glass replacement | $900 - $1,800 |
| Custom trapezoid or pentagon ECO sash replacement | $1,400 - $2,600 |
| Full oversized ECO geometric window replacement (existing frame) | $2,200 - $3,400 |
| Flashing repair with interior trim replacement | $650 - $1,500 |
Price moves with three things: glass size, whether the piece is impact-rated, and how far out of square the opening has drifted. Curved glass costs more than flat glass. Impact lamination costs more than standard. A window that’s shifted by a quarter inch costs more than one that hasn’t. We quote upfront and hold the number. Call (239) 323-5522 for an exact price on your opening - the estimate is free, and it’s in writing.
Why Fort Myers Homeowners Call TruePane Windows & Doors for ECO Window Systems Work
We’ve been doing this in Southwest Florida for over 42 years, and the company carries the name of its founding principle: if the pane is not true, the job is not done. For ECO Window Systems jobs specifically, that means we’ve seen enough of these units come apart in this climate to know what fails first and what to do about it. And because we’re authorized installers on more than a dozen lines - PGT, CGI, CWS, and ES Windows among them - when an ECO window is genuinely beyond saving, we can show you a replacement option side by side with your repair on the same page, not in a separate pitch.
Every job is covered by our 90-Day Done Right Promise and The Keystone Standard: both warranty layers registered in writing, durations stated, before the truck leaves the driveway. Dale Kessler founded this company on that rule, and he still enforces it. If it’s not in writing, it’s not a promise.
FAQs
Most ECO arched and curved windows can be repaired, especially when the failure is a fogging seal, a binding sash, or a worn hinge assembly. Replacement only makes sense when the frame itself is cracked at the miter joints or the glass is broken beyond a single lite replacement. Call (239) 323-5522 and we’ll tell you which one you’re looking at - free.
Independent repairs done with properly spec’d parts and documented in writing do not automatically void your ECO warranty, especially once the unit is past its original coverage window. We register our work and our parts warranty in writing so you have a paper trail if the manufacturer ever asks. That’s The Keystone Standard, and it’s on every job we do.
Most custom ECO-compatible geometric windows are fabricated within two to four weeks, depending on the glass type and whether the shape needs a physical template. Impact-rated curved glass adds time. We’ll give you a firm date on the estimate and we’ll be there when we say.
Yes. In fact, that’s most of what we see. Fort Myers homes with ECO window systems were often installed during builder construction, and the original installer is long gone by the time problems show up. We take those jobs every month and we stand behind the work the same way we would if we’d set the original window ourselves.
Estimates are free at TruePane Windows & Doors. Call (239) 323-5522 and we’ll come out, measure, and give you a written quote with line items and a total that doesn’t move. A live person answers the phone 24 hours a day, 7 days a week.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Myers and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.