Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
CGI
Before
After
Before
After
Before
AfterCGI Door Installation: The Fort Myers Owner’s Guide
CGI door installation in Fort Myers typically runs $450 to $1,100 installed for a standard single door, depending on the specific CGI series and what needs to be swapped. We stock CGI-compatible hardware and weatherstripping on our trucks, so most door work gets done in a single visit. Most owners discover the problem the hard way: the door starts dragging in July, the deadbolt no longer lines up, or they notice daylight sneaking under the threshold after a heavy afternoon storm off the Gulf.
Which CGI Models This Applies To
CGI Windows & Doors builds several impact-rated door lines, and in Fort Myers we see a lot of the Estate Collection, the Classic Collection, and the newer Fusion insulated series. Each series uses different hinge and roller hardware, so the first thing we do on-site is read the sticker on the hinge edge of the slab. That label gives us the series, size, and glass make-up, which tells us exactly which parts fit. If the label has faded under the Florida sun, we measure the door slab thickness and the hinge offset. CGI hardware is not interchangeable across every series, and that is the gotcha that trips up owners who order parts online: a hinge for an Estate door will not seat correctly on a Fusion slab, even if it looks close.
As an independent service provider, we are not affiliated with CGI, but we are an authorized installer for their lines and keep OEM components and quality aftermarket equivalents matched to series specs. For hinges and rollers, OEM usually matters; for weatherstripping, a good aftermarket bulb seal often lasts just as long.
Signs Your CGI Door Installation Is Failing
- The door rubs or binds at the top corner. This is usually sagging caused by a worn top hinge or a slab that has settled over the years. The Southwest Florida heat cycle flexes doors more than most homeowners realize, and a full day of direct sun on a dark door slab can warp even an impact-rated panel.
- The deadbolt does not throw cleanly. The lock and strike plate drift out of alignment when hinges wear or the slab shifts. Forcing the bolt by lifting the handle puts stress on the entire latch assembly.
- You can feel air or see daylight along the bottom sweep. CGI bottom sweeps wear flat and lose their seal, especially if the threshold has been scrubbed clean a few hundred times with a stiff brush. Water from a hard Fort Myers rain will find that gap long before you notice the draft.
- The door closes too fast or not at all. CGI doors run on hinges, not closers, in most residential installs, so a change in swing behavior usually points to hinge wear or a slab that is not hung true anymore.
- Rust staining at the hinge knuckles. Salt air near the Caloosahatchee works on hardware year-round. Once a hinge starts rusting, the bearing surface breaks down quickly and the sag accelerates.
Replacement Cost & What’s Included
In Fort Myers, the typical installed range for CGI door work breaks down like this:
- Hinge replacement: $185 to $340
- Weatherstripping and bottom sweep replacement: $140 to $250
- Threshold replacement: $240 to $420
- Strike plate realignment and latch adjustment: $95 to $160
- Full-slab reset (hanging the door true): $380 to $650
Every quote is a written line item with the parts and labor separated, before any work begins. We do not surprise you at the end, and the price on the sheet is the price on the bill. All CGI door work is covered by our 90-Day Done Right Promise: if it is not right, we make it right, no paperwork fight. Dale Kessler has built TruePane around a rule written on the shop whiteboard, and it covers every door we touch: if the pane is not true, the job is not done.
DIY or Call Us?
CGI door hardware is not high-tension like a garage spring, so there is no serious injury risk in inspecting it yourself. You can safely check whether the slab is level with a simple four-foot level, and you can feel for air movement around the sweep on a breezy day. What you should not do is attempt to re-hang an impact-rated slab. These doors are heavier than standard entry units, the hinge screws are set into the structural frame, and a slab that comes loose mid-project is more than a two-person job. Call (239) 323-5522 and we will send a uniformed technician who measures everything twice and spells out the fix on paper before any work begins.
FAQs
A properly installed CGI door carries a manufacturer warranty on the slab and hardware, and in a salt-air climate like Fort Myers, the hardware is the first thing to go, often between eight and fifteen years in. Which is still very good for this climate, and it is the kind of number our technicians watch for. Call (239) 323-5522 and we will check both warranty layers before we touch a bolt.
A sagging CGI door can often be corrected by re-shimming the hinge and re-tensioning the slab, but a hinge with visible rust or bearing play is a replacement item. Some weatherstripping can be nudged back into place; an actual worn-flat sweep cannot be restored. We will tell you which one you have and quote the repair honestly, not sell you a part you do not need.
Most hinge, sweep, and alignment work is done in one visit of about two to three hours on site, and we keep the common CGI parts stocked in our truck so the job is not waiting on a supply house. Call (239) 323-5522 for an appointment and we will be there when we say we will.
Yes. We carry a rolling inventory of CGI hinges, sweeps, thresholds, and strike hardware specifically because we know which parts fail first in Southwest Florida and we would rather have them on hand than put the job off. We also work with PGT, CWS, and ES Windows parts, so if your home has mixed brands, we can help there too.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Myers and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.